PDA

View Full Version : Westers Garage OBD2 Programming Software



ECMProgrammer
04-13-2007, 08:19
A few people here wanted the parameter listing of editable portions of the 6.5Turbo Diesel computer. This is for the OBD2 system. All values are hex converted to real world numbers to make editing your 6.5Turbo Diesel calibration simple and fun !



ECM Switch Parameters (on off switches to enable or disable functions)

Calibration Options

L56 Light Truck TQ Manage (X)
Turbo Charged (X)
Transmission Diagnostics Type (X) Manual
Increase Idle for Hot Fuel Status (X)
Throttle Following Idle Enable (X)
High Idle Select (X)
PTO Idle Select (X)
Throttle Delay Enable (X)
Turbo Throttle Delay L65 (X)
EGR Throttle Delay (X)
Torque Reduction Active (X)
L65 HD Calibration (X)
Timing Mod (X) Boost and RPM
Passlock Enabled (X)
EVO Message Enabled (X)
Vent Solenoid (X) EPR (0)EGR
Fuel ON CAM Flag (X)
4x4 Calibration (X)
Torque Based Algorthm (X) Active
Traction Control Enabled at WOT (X)
Enhanced Traction Control
Downshift Turns OFF TCC (X)
Rapid Throttle Decrease TCC Off (X)
No Full TCC Lock if A/C ON (X)
Upshift Disables TCC (X)
TCC Enabled in D3 (X)
TCC Enabled in D4 (X)

These are Constants....which have a single editable parameter

# RPM Counts for Adaptive Fuel
ALDL Mode 4 WasteGate RPM Override Limit
Backup Fuel when Cam/Crank Error Exists
Pilot Adjust Hyst Hi Limit
Pilot Adjust Hyst Lo Limit
Fuel Timing Lag Filter Constant
Fuel Timing Negative Compensate
Adapt Cylinder Bal Coolant Temp Enabled
Minimum Throttle Requested Fuel
Maximum Base Throttle Requested Fuel
Max RPM for PILOT INJECTION
Minimum RPM before Fueling Starts
Fuel on CAM Logic (1) Yes
Maximum Transient Fuel Rate
Startup RPM Timing Limit
Maximum Fuel Quantity
Minimum Fuel Quantity
Minimum Throttle Follow VSS
Minimum Baro Update from Boost Sensor
RPM Below which Wastegate = 0%
PWM Minimum for Wastegate Logic
IAT when BOOST is Ramped
BOOST Pressure to Ramp at High IAT
Fuel mm3 Limit When kPa < Desired
Fuel mm3 Limit When kPa < Desired 2
Max Injector PW Change in TQ Management
Maximum Allowed Adaptive Fuel
Actual vs Desired RPM for Adaptive RPM
Maximum Allowed mm3 Adaptive Fuel Rate
TCC Duty Cycle Threshold for TCC Locked
ManTrans Anti-Stall Reduction Fuel mm3
Max Positive Modification to Fuel Pulse
Max Negative Mod to Fuel Pulse
TIMING OFFSET Pump Degrees
Maximum Injection Timing
Pump Degrees Offset Added to 3D Table
Missfire Detection Tolerance
3D Table Injection Timing Adder Constant
P/N Injection Timing Minimum
Idle Speed Override (MODE 4) Maximum
Idle Speed Override (MODE 4) Minimum
ALDL Commanded Glow Plug Max Time
ALDL OFF Before Allowing GP Re-Enable
Minimum RPM for ALDL Mode 4 Timing
Mode 4 Timing Stepper Calibration
Timing Calibration Advance Offset
Minimum Engine Temp for Timing Learn
Timing Calibration Variation Maximum
Timing Calibration Variation Minimum
Time-Out Period to Clear TDC Learn
Limit on Max Time W/O New Closure
Start ECT > "X" Skip T-STAT Fault Set
Engine RPM to Disable EGR Code 32
Fuel Pump Calibration Resistor Min Volts
Fuel Pump Calibration Resistor Max Volts
DTC 61 Turbo Boost High Max
DTC 61 Turbo Boost RPM Limit
DTC 62 Turbo Boost Low Limit
DTC 62 Turbo Boost Upper Limit
DTC 78 Wastegate Logic Failure
DTC 78 Wastegate Logic Failure 2
DTC 78 Wastegate Logic Failure 3
Wastegate kPa Max Delta
Wastegate kPa Min Delta
Wastegate kPa Min Delta 2
Wastegate Control Failure PWM % Default
History Self Clear after 'X' Restarts
MISFIRE Diagnostics Disabled Below 'X'
Minimum RPM for PMD Failure Diagnostics
Lower Boost RPM Limit
P0300 AND P030X Enabled <= 'X' Deg C.
Idle Speed Override Hi MPH Limit
Minimum Throttle for Abuse Management
Minimum Engine RPM for Abuse Management
ABUSE Torque Manage Fuel Reduction Timer
Cruise Governor Lag Constant
Cruise Governor Lead Constant
Maximum Cruise Engine Speed Limit
Minimum Cruise Engine Speed Limit
Minimum Cruise MPH Limit
Minimum Cruise MPH Limit (Cruise OFF)
Maximum Cruise MPH Limit
Maximum Acceleration to Disengage Cruise
Maximum Deceleration to Disengage Cruise
Vehicle Speed Limit Lower Limit
Vehicle Speed Limit Upper Limit
Engine RPM Overspeed Limit
Engine RPM Overspeed Limit Delta
Vehicle Speed Limit 1 Pedal Sensor
Vehicle Speed Limit 1 Pedal Sensor 2
A/C Disable Temp
VTD Learn Counter
VTD Auto Learn Duration
Seed and Key Learn Duration
Auto Learn Cycle # to Enable VTD Learn
EGR (1) Average (2) ON (30 PWM (4) OFF
Engine RPM < Disables Code 32
Desired EGR Pressure Minimum P/N
Desired EGR kPa Minimum (Gear and VSS=0)
Desired EGR kPa Minimum (Gear and VSS>0)
Desired EGR Pressure Maximum
Baro for EGR OFF Determination
Minimum Baro for EGR OFF Determination
Minimum Engine RPM Before EGR Disabled
EGR Error at which Vent is Opened
Minimum MPH for Maximum EGR
MPH at which EGR Reduction On
Maximum Time Delay for Max EGR
Min mSec for BARO update after EGR ON
Upper Fuel Limit for EGR Lookup
Start Enable Setpoint RPM
Idle Enable Delta Setpoint RPM
Idle Disable Delta Setpoint RPM
Engine RPM Lower Limit
Engine RPM Upper Limit
Engine RPM Lower Limit vs Coolant
Engine RPM Upper Limit vs Coolant
Engine RPM Lower Limit Coolant Temp
Engine RPM Upper Limit Coolant Temp
Adaptive Cylinder Balance Setpoint RPM
Low Speed Fueling Latency Setpoint
Start Advance added to Base Timing Timer
Minimum Pre-Glow Time
Maximum Pre-Glow Time < 0 Deg C.
Maximum Pre-Glow Time < 13.5 Deg C.
Maximum Pre-Glow Time < 36.65 Deg C.
Maximum Pre-Glow Time < 65 Deg C.
Post Glow ON Time Scaler 0-100%
Post Glow ON Time Scaler
Post Glow ON Time Scaler 2
Dormant to Pre-Glow ON Transition
Post Glow Duration Scalar
Coolant Temp to Enable Glow Plugs
Coolant Temp to Enable Glow Plugs Offset
Maximum Idle Fuel Rate
Idle Speed Limit A/C ON
Idle Speed for HIGH IDLE Bit Selection
Idle Speed for PTO Active
Cold Ambient Fast Idle Engine Temp Limit
Cold Ambient Fast Idle Speed
Cold Ambient Fast Idle IAT Limit
Minmum Desired Idle Limit
Minmum Throttle Following Idle Speed
Engine ShutOff RPM Limit
Maximum Timing Allowed for Start Fuel
Vehicle Acceleration Limit 1
Vehicle Acceleration Limit 2
Vehicle Acceleration Limit 3
Maximum Fuel Rise/Drop for Torque Reduce
Kickdown Throttle Threshold %
Kickdown Throttle Threshold % 2
Kickdown Throttle Threshold % Hi
Kickdown Throttle Threshold % Hi 2
Abuse Management Enabled Time
Abuse Management Disabled Time
Minimum Throttle for Abuse Torque Manage
Upper MPH for Abuse Mode Enable
Lower RPM for Abuse Mode Enable
Upper RPM for Abuse Mode Disable
Engine Torque High Threshold


Continued...

ECMProgrammer
04-13-2007, 08:22
...Continued

Table listings--Identified by number on the left side. There are a couple hundred more transmission parameters to add, of which we're weighing the pros' and cons'...ultimately, the customer will make the decisions for further updates here. :)

1. System Tables
2. Emissions Tables
3. Fuel Tables
4. Idle Control Tables
5. Spark Tables
6. Transmission Tables

1 Pump Resistor Upper Limit
1 Start Fuel Addition vs ECT
1 ECT Sensor 348 Ohm Scale
1 ECT Sensor 4K Ohm Scale
1 IAT Sensor 348 Ohm Scale
1 IAT Sensor 4K Ohm Scale
1 Fuel Temp Sensor Deg C
1 PreGlow Done to Lamp Timer OFF
1 Firing Order for Scan Tool Cutout Logic
2 Desired EGR Pressure vs Barometric Pressure
2 EGR Integral Gain % Duty Cycle vs Baro
2 EGR Proportional Gain vs Baro
2 Desired EGR Pressure vs RPM and Engine Load
2 EGR Desired vs ECT Modifier
2 Fuel Rate Limit Minimum mm3 vs Baro to Enable EGR
3 Fuel Rate for EGR Limit vs Barometric Pressure
3 Maximum Fuel Rate mm3 vs RPM
3 Maximum Fuel Reduction in Code 78 Mode
3 Fuel Rate mm3 vs Cam Offset Degrees 0 RPM
3 Fuel Rate mm3 vs Cam Offset Degrees 300 RPM
3 Fuel Rate mm3 vs Cam Offset Degrees 600 RPM
3 Fuel Rate mm3 vs Cam Offset Degrees 900 RPM
3 Fuel Rate mm3 vs Cam Offset Degrees 1200 RPM
3 Fuel Rate mm3 vs Cam Offset Degrees 1500 RPM
3 Fuel Rate mm3 vs Cam Offset Degrees 1800 RPM
3 Desired Pulse Width Angle Deg >=80mm3
3 Base Fuel Quantity Coolant Modifier Table
3 BASE FUEL QUANTITY vs TPS and RPM
3 Integral Maximum for Wastegate Logic
3 Integral Delta Scaling for Wastegate vs Boost
3 Delta Scaling for Wastegate vs Boost
3 RPM vs Fuel Rate for DESIRED BOOST kPa
3 EGR Desired MAF Airflow/Cyl Table
3 Throttle Switchover Point 1 vs RPM and mm3
3 Throttle Switchover Point 2 vs RPM and mm3
3 Throttle Switchover Point 1 vs RPM and Throttle%
3 Throttle Switchover Point 2 vs RPM and Throttle%
3 Maximum Injected PW at 0 Fuel Request
3 Abuse Management Fuel Reduction mm3
3 Torque Management Fuel Reduction mm3
4 Startup Fuel Degrees (HiResCounts) vs Coolant Temp
4 Start to Idle Transition Delta RPM
4 Desired IDLE RPM vs Coolant Temp
4 Adaptive Idle Fuel Pulled vs RPM
4 Pre-Glow Offset vs CoolantTemp and Battery
4 Estimation of Glow Plug Temp vs Cool Time
4 Pre-Glow Base vs Coolant Temp and Ign Voltage
4 Post-Glow Base vs Coolant Temp and Ign Voltage
4 Post-Glow Base vs ECT and Glow Plug Feedback
4 Idle Maximum Fuel for Fixed RPM
4 Start Fuel Angle Hi-Res for -40C to -29C
4 Start Fuel Angle Hi-Res for -28 to -17C
4 Start Fuel Angle Hi-Res for -16C to -5C
4 Start Fuel Angle Hi-Res for -4C to +7C
4 Start Fuel Angle Hi-Res for +8C to +19C
4 Start Fuel Angle Hi-Res for +20C to +31C
4 Start Fuel Angle Hi-Res for +32C to +43C
4 Start Fuel Angle Hi-Res for +44C to +55C
4 Start Fuel Angle Hi-Res for +56C to +67C
4 Start Fuel Angle Hi-Res for +68 to +79C
4 Start Fuel Angle Hi-Res for +80C to +91C
4 Start Fuel Angle Hi-Res for +92C to +103C
4 Start Fuel Angle Hi-Res for +104C to 115C
4 Start Fuel Angle Hi-Res for +116 to +127C
4 Start Fuel Angle Hi-Res for +128C to 139C
4 Start Fuel Angle Hi-Res for +140C to 151C
4 Start Fuel Angle Hi-Res for +152C to +163C
5 Pre-Glow Desired Timing Advance vs ECT
5 Timing Adv Modifier vs Engine Coolant Temp and RPM
5 Warm Restart Timing vs ECT
5 Maximum Timing Advance Allowed
5 Minimum Timing Desired vs RPM
5 Timing Compensation for Boost and RPM
5 Baro Timing Modifier Table
5 Fuel Temperature Timing Modifier Table
5 Pump Degree Offset mm3 < 80mm3
5 Pump Degree Offset mm3 > 80mm3
5 BASE TIMING vs MM3 and RPM
5 Fuel Temperature Timing Modifier vs RPM
5 Pilot Fuel Offset Angle mm3 vs RPM
5 Injection Timing IAT Modifier
5 Injection Pump Corr Input mm3 and RPM to Pump Deg
5 Injection Pump Corr Input mm3 and RPM to Pump Deg2
5 Injection Pump Corr Input mm3 and RPM to Pump Deg3
5 Injection Pump Corr Input mm3 and RPM to Pump Deg4
5 Injection Pump Corr Input mm3 and RPM to Pump Deg5
5 Injection Pump Corr Input mm3 and RPM to Pump Deg6
5 Injection Pump Corr Input mm3 and RPM to Pump Deg7
5 Injection Pump Corr Input mm3 and RPM to Pump Deg8
5 Injection Pump Corr Input mm3 and RPM to Pump Deg9
5 Fuel Rate to Pump Degrees vs RPM
6 Normal Upshift/Downshift MPH vs TPS
6 Cruise Upshift/Downshift MPH vs TPS
6 Cold Upshift/Downshift MPH vs TPS
6 RPM Kickdown Upshift Modes
6 Kickdown MPH Shift Modes
6 Predicted Delay Time for Detent Upshifts
6 Base Pressure Rolling Garage Shift vs VSS and TPS
6 Base Pres Rolling Garage Shift Fluid Temp & RPM
6 Base Pres Rolling Garage 'R' Shift Fluid Temp &RPM
6 Normal Base Pressure During Shifts vs Torque
6 Normal Base Pressure During Downshifts vs Torque
6 Desired Shift Time for Normal Shift vs TQ
6 TCC Apply Normal Mode Controlled Threshold
6 TCC Release Normally Controlled Threshold
6 TCC Apply Hot Mode Controlled Threshold
6 TCC Release Hot Mode Controlled Threshold
6 TCC Apply Cruise Mode 3rd and 4th Controlled
6 Torque Reduction at Shift vs Total Torque
6 Pressure Control Solenoid Amps Pressure vs Temp
6 Pressure Control Solenoid (Neg) Table vs Temp
6 Adaptive Cell Preload for Upshifts
6 GearBox Torque Limits vs Gear
6 Base Torque Lookup Table vs RPM and mm3
6 Base Torque Lookup Table vs RPM and mm3 (2)
6 Torque Converter Ratio vs Factored Ratio
6 Inertial Torque at 1-2 Upshift vs RPM
6 Inertial Torque at 2-3 Upshift vs RPM
6 Inertial Torque at 3-4 Upshift vs RPM
6 Average Shift Ratio Threshold vs Shift Torque
6 Adaptive Standard Shift Modifier vs Tq Error
6 Torque Limits Low (1st) and High (2nd) vs Gear


If you have any questions, please email us directly, phone or just post here. I'll try monitor things as best I can between writing template data and testing vehicles. There's a 10000 character limit in the post, so I had to split it up.

Lyndon :)
www.ecmprogrammer.com
Westers Garage
1-888-WESTER-1

ECMProgrammer
04-13-2007, 08:25
Continued...

You'll note I didn't post the trouble code listings. You'll have the option to enable or disable the trouble code test in the software, also.

Note the pricing options on our website in the software section of the price list.

Lyndon
www.ecmprogrammer.com
Westers Garage
1-888-WESTER-1

gmctd
04-13-2007, 08:46
Thanks, Lyndon - I appreciate the effort and time taken to assemble these lists

AndyL
04-13-2007, 09:22
Major Thanks Lyndon,

Do any of your reflashes come bundled?

ECMProgrammer
04-13-2007, 18:32
When you order a personal version, we also send the calibration that was for your truck based on your VIN.

Lyndon
www.ecmprogrammer.com
Westers Garage
1-888-WESTER-1

bahamablue
05-04-2007, 18:07
so with all the parameters you can edit, is it possible to drop in a 12v cummins in place of the 6.5 and still have the computer control the 4l80e and the gauges? I want to drop a cummins into a 98 ext cab 4x4 body and have the gm ride with all the benefits of the cummins. Can you do something custom for this application?

DA BIG ONE
05-05-2007, 00:14
so with all the parameters you can edit, is it possible to drop in a 12v cummins in place of the 6.5 and still have the computer control the 4l80e and the gauges? I want to drop a cummins into a 98 ext cab 4x4 body and have the gm ride with all the benefits of the cummins. Can you do something custom for this application?

I'm guessing using a 12v say 94 to 98 all that would be needed would be a tps & speed signal to run a 4L80e while leaving the IP harness disconnected (its would throw codes relating to IP).

I've spent lots of time trying to get a standalone tranny controller for my burb but the autotrac t-case becomes an issue because it's intergrated into the ABS too.

ECMProgrammer
05-05-2007, 09:13
I'm guessing using a 12v say 94 to 98 all that would be needed would be a tps & speed signal to run a 4L80e while leaving the IP harness disconnected (its would throw codes relating to IP).

I've spent lots of time trying to get a standalone tranny controller for my burb but the autotrac t-case becomes an issue because it's intergrated into the ABS too.

You'd just disable the codes relating to IP.

Lyndon
www.ecmprogrammer.com
Westers Garage